LuminaCAD

v3.5

Parametric 3D-printable lamps · Bambu Lab X2D

Presets

Dimmer Level 95%

Warmth (Kelvin) 2400K

Matte Polymer:

2D Section & Fit 33° Cone

Lamp Size

Ø 246 × 491 mm (19.33")

Filament

~485 g (5 Parts)

Tallest Part

Stem: 253 mm / 260 mm Max

Bambu Lab X2D

All 5 Parts Fit 256×256×260mm

Lamp Parameters

19.33" Reference Cone Lamp

Lamp Type

Full 19.33" (491mm) 5-part system: G¹ Rounded-Apex Cone Shade + Twist-Lock White Diffuser Disc + Hollow Stem + Pillowed Pebble Base + Plug-In 24V COB LED Core so every piece fits inside the Bambu Lab X2D (256×256×260mm).

Shade & Apex

mm / °

Shade Silhouette Mode

Shade Height 198 mm (7.80")

Bottom Skirt Radius (Ø 246mm) 123 mm (4.84")

Top Apex Tip Rounding (G¹ Fillet) 16 mm

Bottom Rim Bullnose Lip 11 mm

Diffuser Disc Thickness (White) 2.0 mm

Diffuser Wall Thickness 2.0 mm

Stem & Base

Visible Stem Height 225 mm (8.86")

Stem Outer Radius (Ø 44mm) 22 mm

Stem Bottom Tuck Radius 9.5 mm

Pebble Base Radius (Ø 196mm) 98 mm (3.86")

Pebble Base Height 68 mm (2.68")

Side Roundness 92%

Base Top Dome (0% = Flat) 0%

Drum Shade & Base

Drum Shade

Shade Height (to rim crest) 195 mm (7.68")

Shade Radius (Ø 216mm) 108 mm (4.25")

Symmetrical Shade (top mirrors bottom)

Top Corner Rounding 38 mm

Corner Rounding (bottom) 60 mm

Top Opening Ø (above the bulb) 76 mm

Dish Entry Slope (45° = plain funnel) 60°

Rim Crest Fillet (flat crest = 2.12×) 5 mm (flat 10.6)

Shade Wall Thickness 2.0 mm

Horizontal Rib Depth (0 = smooth) 1.0 mm

Rib Spacing 6.0 mm

Socket Base

Base Radius (Ø 126mm) 63 mm (2.48")

Visible Base Height 78 mm (3.07")

Shade Collar Clearance (per side) 0.20 mm

E26 Socket & Bulb

Socket Hole Ø (measure your socket) 40.0 mm

Socket Mouth Above Plate 30 mm

Bulb Length (A19 ≈ 110mm) 110 mm

Pendant-cord E26 socket clamps through the 3mm top plate with its shade ring. Feed the plug down through the hole, out the open bottom and through the cord notch at the back. The shade drops over the base's locating collar; print Fit Test E to check the collar clearance against your shade before printing the base. PLA softens at ~60°C: LED bulb only (≤10W / 60W-equivalent), never incandescent or halogen. The top opening vents heat over the bulb; keep the bulb gap (2D panel) ≥ 15mm.

Light Engine

Internal Light Engine

Joint Fit Clearance (per side) 0.10 mm

Stem tenon, LED core plug & disc hub. Lower = tighter. Re-export Fit Test A after changing.

Internal LED Core Height 110 mm

Wire Conduit Hole Ø (Stem & Base) 8.5 mm

Bambu Lab X2D Printing Breakdown:

At 19.33" (491mm) total height, print Part 1a (Shade Cone: 246×198mm), Part 1b (Diffuser Disc in thin white — slide its 3 tabs up through the cone's slots and twist), Part 2 (Stem: 44×253mm), Part 3 (Base: 196×68mm), and Part 4 (Plug-in COB LED Core: 30×125mm). Every part stays inside your X2D's 256×256×260mm volume.

Surface Texture

Shade Surface Finish

Mesh Smoothness (Radial Segs) 180

Saved Models

checking…